How to Build the Fastest Pinewood Derby Car (2024)

Family HandymanUpdated: May 12, 2023

Step 1

Bake the Wood Block

Family Handyman

Wood holds water, and water adds weight. You want weight, but you’ll want the weight where it’s most beneficial. Pre-heat your oven to 250 degrees, then bake your block for 2 hours. All the water evaporates, allowing more control during the next few steps.

Step 2

No Fancy Shapes

Family Handyman

This is where some might differ in their approach to the Pinewood Derby. It’s okay to get creative with the look and design of your car. On the flip side of that, if your main goal is speed, you’ll need to keep it simple.

To go fast, it’s all about aerodynamics, and the best shape is a simple wedge. Just like a spoiler on the rear of a sports car, the wedge shape allows as much air to flow over the top of the car without hinderance while keeping the car pinned to the track.

The wedge here tapers from 5/16-in. to 7/8-in. A band saw and push stick are the quickest way to cut the wedge (wear safety gear and follow safety guidelines), but a coping saw works just fine. Sand the car body up to 220-grit.

Step 3

Add Weights to the Pinewood Derby Car

Family Handyman

The heavier your car is, the faster it’ll be, but it’s the location of the weight that makes the most difference. You can add small weights to the wood body of the car, so long as the it doesn’t exceed the total weight limit. The weight limit is five ounces, but check the rules for your local contest to be sure.

The ideal placement for the center of gravity is 7/8-in. in front of the rear axle. Too far forward and you’ll lose potential energy. Too far back and your car will pop a wheelie, ruining any chance for a win.

To make sure your car doesn’t exceed the weight limit, weigh all the parts before assembly. Leave a little wiggle room for paint, glue, stickers, etc.

Tungsten is the best weight because it’s heavy for its volume, allowing more precise placement.

Step 4

Engineer the Wheels

Family Handyman

There’s not much wiggle room for what you can do with the official wheels you have to use, but you are allowed to remove seems or imperfections in the plastic.

To do that,you can sand the wheels, and when you do, make sure to sand them as smooth as possible. Also, most wheels aren’t perfectly round right out of the package so getting them as round as you can helps a lot.

Step 5

Smooth the Axles

Family Handyman

The stick nail axles included in the kit have little ribs along the shank and a flat nail head, both of which cause friction, slowing the wheels. Smooth the axles by putting them into a drill press and sanding them up to 2000 grit.

With the nail still in the drill press, round the inner face of the nail head with a file and sand it smooth.

Secure the axles to the car body, add graphite, spin the wheels and time the spin duration. A good axle set up will spin for about 45 seconds.

Step 6

Ride on Three Wheels, if Allowed

Family Handyman

To reduce even more friction against the track, raise one of the front wheels just slightly higher than the other so that it doesn’t touch the track. If you try this step, the center of balance needs to be exactly down the centerline of the body so that the car doesn’t wander on the track. Again, check with your local rules to see if this is allowed.

Step 7

Use Graphite Lubricant

Family Handyman

Because only dry lubricant is allowed, the most common solution is graphite. Where do you use the graphite? Everywhere; wheels, axles, axle slots. The type of graphite doesn’t matter. It all works, so buy the cheap stuff. Spin each wheel numerous times to help the graphite break down for maximum performance.

Step 8

Cover the Wheels

Family Handyman

This is an aerodynamics lesson. Exposed wheels allow air to flow over the front and then get caught under the rear. Next time you’re driving, notice how many exposed wheels are on the road. None.

To make “fenders”, outline their shape and mark the wheel centers on 1/2 in. pine. Drill a hole with a 1-1/4 in. Forstner bit at the wheel center, and then cut out the rest of the shape with a handsaw. Glue the fenders to the body.

Step 9

Quick Starter

Family Handyman

Most derby cars are designed so they don’t start until the starting pin fully drops. But there’s a simple way to let the car start inching forward while the pin is moving, giving you a head start. Unfold a paper clip, making it a three-sided rectangle. Mark and drill hole locations on the front end of the car, ensuring that once assembled, the paperclip doesn’t extend past the front of the car. Drill 1/4-in. into the body and glue the paperclip ends into the holes with CA glue.